[ATK] --------------------------------------------------------------------------- ATK - Protein-Skimmers, Pumps and Modul-Filter --------------------------------------------------------------------------- ATK-Protein Skimmer Typ Junior [Bild Junior]The protein skimmer Type Junior represents an expansion of our range of hight performance protein skimmers. It was specially developed for installation in cabinets beneath aquariums and is suitable for installation both outside and inside of the filter chamber / standard height only ca. 55cm including foam cup) Combined with our pump MP 5536 or an EHEIM Type 1060, the ATK Protein Skimmer Junior independently draws in 300 to 400 litres of air per hour through its Venturi nozzle which is mixed with the water. Above this, in the foam tube of the foam cup, the proven foam sieve provides for the necessary settling of the wet foam, which leads to a very effective protein skimming. When using the EHEIM pump Type 1060 as an sumergable pump ( which stands on the intake basket ) only 4cm of water are necessary in the filter tank. Application is simple: Make a short curved or straight pipe or tube connection ti the intake connecting piece on the bottom of the skimmer ( 19 mm ) Connect the outlet nozzle on the top of the skimmer to the filter reservoir, provided that the skimmer isn't already immersed in the filter reservoir. Connect the air tube to the air noozle ( under the foam beaker ), lead the tube over a fixed point higher than the foam beacker and close the tube with a clamp. Turn the pump on and adjust the water level in the skimmer by regulating the outlet such that the water level remains at the level of the foam sieve with the air tube clamped. The degree to which the water is to be wet or dry skimmed can be adjusted by the amount of air admitted by the tube clamp, which can be appropriately opened or closed. Technical specifikations: height of reaction pipe ca. 37 cm height of foam containe ca. 16 cm total height ca. 55 cm necessary clearance ca. 57 cm diameter ca. 20 cm intake nozzle 20 mm tube connector outlet 25 mm PVC Rohr indepedant air intake 300 - 400 litres per hour necessary pump ATK MP 5536 (not-submergable pump) or EHEIM 1060 (submergable pump) maximum aquarium size 750 litres (according to trimming) --------------------------------------------------------------------------- Protein skimmer Typ Disperator EA 45 300 EA 45360 Available in 2 standard sizes [Disperator]EA 45 300 0,70 m plus foam beaker 0,20 m EA 45 360 1,30 m plus foam beaker 0,20 m * exterier diameter 200 mm * foam beaker volume 3,00 litres * water flow max. 1.500 litres * formation of bubbles without exhaust through a dispersant * motor consumption 45 W * air intake automatic up to 420 l/h depending on salt and colloid contens * diameter os air bubbles 0,1 - 0,3 mm * total surface area of air bubbles per hour 10.000m² * contact time at 1200l/h water rate and 1,3m height: 3 min.or 180 seconds * dwelling time of water under same conditions: 1,8 minutes or 108 seconds. * oxygen saturation of process 100 % too without Dispersant deliverable (for air-stone working) DBP 3525861 US-Patent 4.764.311 --------------------------------------------------------------------------- Venturi I + II Protein skimmer for big tanks I to 10 000 litres II to 20 000 litres [Venturi]Mixing chamber polyethylene diameter 400 mm height ca. 500 mm Reaction pipe plexiglas diameter 200 mm height Typ I 700 mm height Typ II 1300 mm Foam pipe diameter 90mm height ca.330 mm Foam beaker diameter 200mm height ca. 400 mm Total height with foam beaker Typ I 1600 mm Total height with foam beaker Typ II 2040 mm Supply pipe up to 2 m straight diameter 40 mm More than 2 m curved diameter 50 mm Venturi nozzle PVC diameter 32 mm Air connection diameter 8 mm Drainage pipe skimmer diameter 50 mm Air regulation either by angle seat valve or clamp Air intake is automatic Regulation of water level by means of angle seat valve on drain Headwater pump: alternating current ( I - 180 W A/C) performance II - 270 W Headwater pressure I = 0,45 bar II = 0,50bar Headwater quantity I - 4 600 l / h II - 9 000 l / h Installation is possible next to and, in connection with a circulation pump and reservoir, also above or below the aquatic installation. Ozonization is possible, because all parts that come in contact with ozonized water are absolutely ozon resistant, it is only recommendend in connection with a redox potential control and adjustment installation. Included in the delivery package are: * complete skimmer * Foam cup * Headwater pump with screws * venturi nozzle and angle seat valve Not included in the delivery package are: * ball valves * air volume gauge * gauge and adjustment equipment * arcs, pipe and installation All All further necessary artikels can be purchased through us. Important: The water to be skimmed must be mechanically pre-filtered in order to prevent the pump from malfunctioning. --------------------------------------------------------------------------- Mammoth contact pipe Polyetylen diameter 1.000 mm height 1.000 mm foam pipe plexiglas diameter 200 mm height 1.000 mm foam outlet without adaptor diameter 90 mm foam outlet with adaptor diameter 40 mm total height with foam outlet 2.350 mm intake pipe up to 2m straight diameter 63 mm more that 2m / curved diameter 100 mm Injector PVC diameter 50 mm air connection diameter 20 mm outlet pipe diameter 90 mm air regulation by means of angle scat valve air intake: automatic maximum 28.000 l / h with correct 2.000 l / h admustment water level regulation by angle seat valve headwater pump three phase current 400V 2.200 W Theadwater pressure 2,0 bar headwater level 15.000 l/ h duration 3,15min. or 189 sec. contact time 2 min. or 120 sec. Installation either next to, under or above the unit in connection with a circulation pump parallel to a biological filter system. Ozonization is possible, because all parts that come in contact with ozonized water are absolutely ozon resistant, it is only recommendend in connection with a redox potential control and adjustment installation. --------------------------------------------------------------------------- Module-Filter Type SE 1 and SE 05 Notices: The Module Filter is a further component of our range produkcts for sea water aquatics.Due to its spezifications, the Module Filter is partikularly suitable for installation under the aquarium. This filter meets demands for operating a complete system with very little energy consumption this is due especially to the high flow of water that this filters allows. operation with only one ATK pump is possble since. the high flow performnce also allows for needed water flow to be produced in the aquarium. Filtering is done by means of batting in the form of cartridges.Batting cartridges offer an uncomplicated means of removing filth and debris from aquarium water. Due to the ease of removing the cartridges from the filter, the Module Filter is especially user - friendly. Silting is thus prevented and makes a quarterly tank cleaning unnecessary. A special feature of the Module Filter is its expandability with additional modules. The Module Filter is prepared for the installation of the protein skimmer Typ ATK - Junior. Additional supporting pumps are not necessary, since the performance of ATK pumps is adaquate ( Model 6055 and above) A further sensible expansion possibility is the ATK Mini Automatic Refiller. This unit is simply placed in the prepared level chamber and connected to the reservoir or pressure reducer. Of course there are additional types of filtermaterials that can be fitted to the ATK Module Filter, such as carbon, zeolite, etc. [Bild Modul] specifications: lenght SE I 800 mm SE 05 600 mm width 500 mm height 400 / 500 mm Material: polypropylene absolutely neutral Filter construction 4-chamber system with 5-chamber system covering with covering level chamber pre-filter chamber, none chamber for additional substratum main filter chamber clear water chamber Filter substratum cartridges 29 14 Water flow to max. 10 000 l / h 6.000 l /h for aquarium sizes: from 500 to max. 1 500 litres volume Module additions Protein skimmer Mini automatic ATK-Junior refiller --------------------------------------------------------------------------- Magnetic Rotary Pumps Special Features: [Bild Pumpe] * 100 % sea water resistant * no rotating shaftsealings * no water thermalization by motor head * energy efficient * water lubricated plain bearings * quiet operation * pump head pivotal up to 90° * high efficiency of operation from 5 000 L / h - 20 000 l / h. The seal of the shaft duct is one of the most critical parts of rotary pumps. Most pump malfunctions are caused by poor seals and bearings. The ATK magnetic Rotary Pump is permanently magnetically driven by means of a synchronic clutch. A permanently magnetic external rotor, powered by a normal electric motor, efficiently transmits rotational momentum to a permanently magnetic internal rotor (impeller). Between the external and internal rotor there is a split plate or split head, which seals the product flushed interior from the atmosphere.The internal magnetic rotor and the impeller share a common shaft. Rotary pumps with magnetic drive have the advantage over split pipe motor pumps that they are not dependant on cooling by means of the feed medium and thus do not head it up. Since the split plate or split head in ATK Magnetic Rotary Pumps is made of plastic, in contrast to split pipe motor pumps, corrosion is ruled out. The permanent magnets consist of sintered material and need no additional corrosion protection due to their high corrosion resistance. Technical subject to change --------------------------------------------------------------------------- Dealer and technical support please:: ATK - Aquarientechnik Bonner Str. 63 53474 Gimmigen Tel.: 49 ( 0 ) 26 41 - 16 78 Fax : 49 ( 0 ) 26 41 - 28 98 4 --------------------------------------------------------------------------- [top of page][to index][E-Mail] Entwicklung ©1997 A.Weber