SphinX mechanical hardware

J. Bąkała, J. Sylwester, Z. Kordylewski, M. Kowaliński, W.Trzebiński, S. Płocieniak

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland


Principles of the mechanical construction of multi-channel X-ray photometer SphinX will be presented. The vibration-acoustic tests of the instrument performed last year in Prague will be described.


В докладе представлена будет конструкция и принципы действия рабoты многоканального рентгеновского фотометра СфинкС. Обсуждаются результаты вибрационных испытаний технологического образца прибора, которые были проведены в Праге.


presentation   (6.8 MB)




System of recovery and distribution of scientific information

A. Buslov

IAF MEPHI, Moscow, Russia


В работе описаны принципы организации приема, первичной обработки и экспресс-анализа данных, а так же особенности аппаратно-программного обеспечения Центра экспресс-обработки, накопления и хранения данных, в спутниковом эксперименте КОРОНАС-ФОТОН. В рамках спутникового эксперимента КОРОНАС-ФОТОН планируется осуществлять сбор информации с КА ежесуточно на 4-х витках (двух восходящих и двух низходящих) в объеме 1 Гб. Прием будет осуществляться средствами НЦ ОМЗ одновременно по двум частотным радиоканалам (8,128 и 8,320 МГц) на комплекс приема - ПК-7 (основной) и на резервный комплекс ПК-2. Информация в виде двух файлов целевых данных, снабженных файлами сопутствующей информации (отражающими параметры, характеризующие качество приема, параметры приемного комплекса и т.д.), выкладывается на FTP-сервер НЦ ОМЗ в течении часа после сеанса связи. В течении трех часов после приема данных в ЦЭОНХД ИАФ МИФИ данные должны быть выложены на сервере МИФИ для участников эксперимента. Перед этим проводится сшивка из нескольких файлов исходных телеметрических данных в один, а так же разделение информации по цифровым источникам, относящимся к различным каналам приборов комплекса научного оборудования "Фотон". Данные со всех приборов используются разработчиками для проведения экспресс-анализа и формирования набора команд, предназначенных для управления работой приборов и осуществления принятой программы исследований. Все предложения по командам управления п программам измерений поступают в МИФИ, где по принятым процедурам будет осуществляться формирование набора команд для очередного сеанса управления комплексом научной аппаратуры.

presentation   (7.5 MB)



Experience with the software of Czech HXRS X-ray photometer aboard the DoD satellite

Martin Cupák

CupySoft, Praha, Czech Republic
(Provider of the HXRS flight SW and ground-based data processing SW)


The HXRS means a Hard X-Ray Spectrometer, i.e. an instrument which was monitoring solar X-ray flux in eight energy bands between 10 and 200 keV. The instrument was controlled by an onboard computer and provided automatic band division shifting and integration time changing according to the intensity level of X-ray flux.
There were two interesting features of the flight software which we would like to emphasize: the optimized routine for counting X-ray photon events in energy bands and the time-efficient inflight calibration algorithm. Brief description of the HXRS ground-based data processing SW will be presented as well.

presentation   (300 KB)



Instrumentation onboard Hinode and examples of data obtained.
Brief discussion on scientific topics to be studied with XRT


Frantisek Farnik

Astronomical Institute, 251 65 ONDREJOV, Czech Republic



presentation   (10.4 MB)



The fast x-ray monitor (FXM) based on yap(ce) scintillator for Coronas-Photon satellite project

E. Fedorovykh

IAF MEPHI, Moscow, Russia

Представлено описание прибора «Быстрый рентгеновский монитор» (БРМ), который входит в состав научной аппаратуры проекта КОРОНАС-ФОТОН. Прибор предназначен для измерения временных характеристик излучения Солнца в рентгеновском (X-ray) диапазоне энергий от 20кэВ до 600 кэВ с временным разрешением до 2-3 мс. БРМ состоит из блока детектора БРМ-Д, блока высоковольтного питания ВВИ-5, установленных вне гермоотсека, и блока электроники БРМ-ЭМ, установленного в гермоотсеке. - В основе детектора БРМ-Д используется сцинтиллятор, выполненный на основе кристалла иттрий-алюминиевого перовскита (ИАП), активированного церием (YAlO3(Ce)). ИАП имеет ряд преимуществ перед другими кристаллами, используемыми в детекторах рентгеновского излучения, например перед NaI(Ta):
- меньшее время высвечивания (27нс вместо 230нс),
- большая плотность (5,55г/см3 вместо 3,67г/см3),
- является негигроскопичным.
Эффективность высвечивания ИАП составляет 40% относительно эффективности NaI(Ta), максимум спектра излучения сцинтиллятора приходится на длину волны 350нм. В блоке БРМ-Д происходит регистрация рентгеновского излучения в следующих шести дифференциальных энергетических каналах и в двух интегральных.

Номер каналаШирина канала, кэВ
120 - 30
230 - 40
340 - 50
450 - 70
570 - 130
6130 - 600
720 - 600
8> 600

Для предотвращения изменения коэффициента усиления ФЭУ при больших потоках рентгеновского вспышечного излучения в блоке БРМ-Д предусмотрена система стабилизации, позволяющая поддерживать коэффициент усиления ФЭУ на одном уровне путем управления высоковольтным питанием детектора. Время реакции системы стабилизации 0,1с. В докладе приведены параметры прибора, полученные ив ходе его наземной отработки.

presentation   (3.6 MB)



SphinX calibration program BESSY and XACT

S. Gburek

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

SphinX spectrometer is going to be fully calibrated before the launch. The first extensive test of the instrument characteristics will be performed using BESSY synchrotron source (Berlin). These tests will reveal the actual instrument's resolution and effective area. The absolute calibration accuracy against the synchrotron beam is expected to be better than 5%. The second part of the calibration will take place at Palermo University (XACT facility) in order to extend the BESSY calibrations. A high output X-ray source with precisely controlled and monitored flux will be used there. In addition a test of the SphinX fluorescence blocks will be made in order to check the instrument in-flight calibration capabilities. Calibration setups and expected results of these calibration programs will be discussed in details.


presentation   (18.8 MB)




The pile-up in SphinX detectors: how we can calibrate it beforehand and follow in-flight

S. Gburek

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

The principles of SphinX measurements, electronics and operation modes are described. Results of Monte Carlo simulations of SphinX measurements are presented, discussed and compared for various solar activity levels. In particular an analysis of bias due to pile-up effects and lost-events is performed.


presentation   (600 KB)




Structure of Coronas-Photon onboard telemetry and command systems

A. Glyanenko

IAF MEPHI, Moscow, Russia

In the talk a structure of onboard data acquisition, preliminary processing and registration of scientific information system and the structure of control for the Coronas-Photon project is discussed. In the Coronas-Photon project some systems for control and data acquisition are used:
- Onboard Complex of Control (OCC) including satellite control devices, satellite onboard computer, onboard time and synchronization system;
- Satellite Telemetry System (STS);
- Scientific Telemetry System (SSRNI);
- Block of control and connections of scientific complex (BUS-FM).
For the control of all scientific devices (SD) of Coronas-Photon the next resources are available:
- Up to 160 pulse commands with duration 0,1-0,3 sec and amplitude that is equals to satellite power; “dry contacts” – pulse on/off and (switch on)/(switch off) type (OCC→BUS-FM).
- Special commands “shadow/light” and “bad/good’ (location of the satellite in high latitudes or in the SAA region), (OCC→BUS-FM).
- 16-bits digital commands (UKS) to operate by scientific devices (OCC→SSRNI by 1553b-channel).
For data acquisition in Coronas-Photon project the next resources of two telemetry systems are used by SD:
- Satellite Telemetry System (STS) – 131 digital, 34 analogs and 21 thermo-sensors;
- Scientific Telemetry System (SSRNI) with the next possibilities:
   - Up to 24 individual information channels for SD with link speed for one channel - 62.5 kbits/s or 125 kbits/s
   - Total mass memory up to 1.5 GB, the memory allocation between SD’s is installed according to quotas.
   - Additional data from STS throw OCC to SSRNI by 1553b–channel;
   - Ground data link with link speed 7.68 Mbits/s or 15,36 Mbits/s at frequency 8,2 GGz (depending on coding algorithm in the link session).
Including into operational network units not only from scientific complex, but all needed units from satellite systems. It is allowed to realize a flexible, convenient infrastructure for management and data acquisition from scientific equipments and to expand opportunities of experiment.


presentation   (600 KB)




Envisaging SphinX: expected DEM distributions for selected solar activity levels

A. Kępa, B. Sylwester, M. Siarkowski, and J. Sylwester

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

An analysis of differential emission measure distributions (DEM) is one of the scientific goals of SphinX instrument. I will present the DEM distributions for a set of flares belonging to different GOES classes from the range B5.6 - X1. As the input data we have used absolute fluxes observed by RESIK in several spectral bands (lines+continuum). Respective emission functions have been calculated using the CHIANTI v. 5.2 atomic data package. The DEM distributions have been calculated using 'Withbroe - Sylwester' multiplicative, maximum likelihood iterative algorithm. The skills gathered will allow to perform the DEM calculations based on the SphinX data.


presentation   (1.1 MB)




Monitor of solar XUV/EUV irradiation PHOKA

A. Kochemasov

IAF MEPHI, Moscow, Russia

В Институте астрофизики Московского инженерно-физического института создается прибор ФОКА, предназначенный для измерения плотности потока солнечного излучения (интегрального от всего солнечного диска) в диапазонах длин волн 1-11нм, 27-37 нм и в линии атома водорода Ly-α (121,6 нм). Минимальное временное разрешение прибора составляет 0,1с. Прибор будет установлен на российском научном спутнике КОРОНАС-ФОТОН. Спутник будет иметь постоянную ориентацию на Солнце. В момент входа спутника в тень Земли и выхода из нее прибор ФОКА будет регистрировать излучение, прошедшее через земную атмосферу (т.н. оккультационные измерения). Запуск спутника планируется в 2008 г.
Информация, полученная прибором ФОКА будет использоваться для:
- изучения развития солнечных вспышек и вариации солнечного излучения;
- изучения состояния верхних слоев атмосферы Земли.
В таблице представлены каналы прибора ФОКА и соответствующие им диапазоны измеряемого излучения. Основные каналы (№ 2,3,4) будут проводить постоянные измерения, а калибровочные каналы (№ 5,6,7) будут задействоваться в полете периодически для оценки деградации основных.


№ каналаОптический фильтрТолщина фильтра, нмДиапазон, нмПримечание
Основные каналы
1отсутствует- <1100 оптический канал
2Ti/Pd200/1001 - 11напыленный фильтр
3Cr/Al100/20027 - 37напыленный фильтр
42 внешних фильтра - 116 - 125Лайман-альфа канал
Резервные (калибровочные) каналы
5Ti/Pd200/1001 - 11напыленный фильтр
6Cr/Al100/20027 - 37напыленный фильтр
72 внешних фильтра - 116 - 125Лайман-альфа канал


В качестве чувствительных элементов выступают кремниевые фотодиоды AXUV фирмы IRD (США). В каналах 1-11нм и 27-37нм используются фотодиоды с нанесенными на них металлическими фильтрами. В каналах Ly-α установлены по два внешних интерференционных фильтра. Оптический канал не имеет фильтров и не дублирован. Электронный тракт каждого канала состоит из преобразователя фототок- напряжение - частота.
Для учета фонового сигнала от видимого света, который для каналов 1- 11нм и 27-37нм сопоставим с полезным сигналом, в составе блока детекторов имеется колесо кварцевых фильтров. Полезный сигнал будет определяться как разность двух сигналов: сигнала при измерении с открытой апертурой и с надвинутым кварцевым фильтром, пропускающим видимое излучение и полностью задерживающим жесткое УФ излучение.
Предполетную калибровку прибора планируется провести во ВНИИОФИ и национальном метрологическом институте PTB (ФРГ).


presentation   (2.4 MB)




Flare detection algorithms - experience from Coronas - Diogeness

Z. Kordylewski

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

The flare detection algorithms have been developed at SPD SRC in Wroclaw and incorporated into the software of Diogeness instrument flown on Coronas-I, Coronas-F. These algorithms have been used in order to trace on-line the X-ray signal with the aim to detect flares and provide respective flare-flags. The flare flags were used for other instrument systems to change the mode of respective instrument operations. One of these algorithms - already flight tested- has been slightly modified in order to be used in SphinX. We performed 'ground-tests' of its validity using the real X-ray data collected from the RESIK instrument, placed aboard the Coronas-F. For RESIK, we have a large database covering various periods of solar activity. RESIK data contain also the information about the transition across the radiation belts, SAA, spacecraft nights with respective background and telemetry noise. Therefore, we were able to identify the weak points of the algorithm in a given circumstances. The results of this exercise will be presented and possible solutions to be used for SphinX discussed.


В рентгеновских спектрометрах ДИОГЕНЕС на объектах КОРОНАС измерения потока рентгеновского излучения Солнца использовались в реалном времени до определения параметров возникающих вспышек. По этих результатах проводилось изменение режимов работы спектрометров. Очень простый алгоритм был основан на анализе потока излучения и его изменениях в довольно длительных промежутках времени. Проверка алгоритма, выполнена по данных, полученных с помощью спектрометра РЕСИК, показала слабые точки этого метода. Для следуюшего эксперимента с рентгеновским спектрометром СФИНКС разработано улучшенный алгоритм, основанный на анализе не только потока, но тоже его производной по времени. Большой трудностью является преривная запись потоков рентгеновского излучения, наблюдаемых на борту объектов типа КОРОНАС, которые на каждом витке несколько раз проходят через радиационные пояся и тень Земли. Тоже разнообразие формы развития и затухания вспышек, а также иногда одновременное возникновение двух вспышек усложняет алгоритм. На всех этапах доработки алгоритма ведется его проверка по данным с прибора РЕСИК.


presentation   (1.6 MB)




Scientific Objective and observational capabilities of Coronas-Photon project

Y. Kotov

Astrophysics Institute. Moscow Engineering-Physics Institute (Russia)

"Coronas-Photon" mission is the third satellite of the Russian Coronas program on solar activity observation. The main goal of the Coronas-Photon is the study of solar hard electromagnetic radiation in the wide energy range from UV up to high energy gamma-radiation (~2000MeV). Scientific payload for solar radiation observation consists of three type of instruments: 1) Monitors (“Natalya-2M”, “Konus-RF”, “RT-2”, “Penguin-M”, “BRM”, “Phoka”, “Sphin-X”, “Sokol”) for spectral and timing measurements of full solar disk radiation with timing in flare/burst mode up to one msec. Instruments “Natalya-2M”, “Konus-RF”, “RT-2 will cover the wide energy range of hard X-rays and soft gamma-rays (15keV to 2000MeV) and will together constitute the largest area detectors ever used for solar observations. Detectors of gamma-ray monitors are based on structured inorganic scintillators with energy resolution ~5% for nuclear gamma-line band to 35% for GeV-band. PSD analysis is used for gamma/neutron separation for solar neutron registration (T>30MeV). “Penguin-M” has capability to measure linear polarization of hard X-rays using azimuth are measured by Compton scattering asymmetry in case of polarization of an incident flux. For X-ray and EUV monitors the scintillation phoswich detectors, gas proportional counter, CdZnTe assembly and filter-covered Si-diodes are used. 2) Telescope-spectrometer TESIS for imaging solar spectroscopy in X-rays with angular resolution up to 1arcsec in three spectral lines and RT-2/CZT assembly of CZT pixels with coded mask aperture. 3) Two semiconductors monitors for charge particle energy spectra and angular resolution registration. Satellite platform and scientific payload is under construction to be launched in June 2008. Instruments are provided by Russia, India, Ukraine and Poland. Satellite orbit is circular with initial height 550km and inclination 82.5degrees. Accuracy of the spacecraft orientation to the Sun is better 3 arcmin. Nominal mission lifetime at least 3 years with extended 5 years.


presentation   (10.9 MB)




SphinX electronics and software

M. Kowaliński

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

The schematic representation of the instrument's electronics will be described. Details of the software will be presented together with respective Electrical Ground Support Equipment (EGSE). The cooperation of SphinX within TESIS complex will be discussed.


presentation   (470 KB)




Diagnostics of Non-thermal Electron Distribution using synthetic and flare spectra

A. Kulinova and E. Dzifcakova

Dep. of Astronomy, Physics of the Earth and Meteorology, Faculty of Mathematics, Physics and Informatics, Comenius University Bratislava, Slovakia

The observed X-ray spectra of the impulsive phase of the solar flare very often can not be explained by using the assumption of the electron Maxwell's distribution. The unusual spectral line ratios indicate the presence of a non-thermal electron distribution. The satellite line and the allowed lines belonging to ions in different degree of ionization seem to be suitable for diagnostics. The diagnostics has been applied on the RESIK X-ray spectra of the solar flare.


presentation   (1.7 MB)




Experiment TESIS on board Coronas-Photon

S. V. Kuzin, S. A. Bogachev, I. A. Zhitnik, A. A. Pertsov, A. P. Ignatiev, A. M. Mitrofanov, V. A. Slemzin, S. V. Shestov, N. K. Sukhodrev,

P.N. Lebedev Physical Institute of Russian Academy of Science, Leninskij prospekt 53, Moscow 119991, Russia

O.I. Bugaenko

Astronomical Institute, Moscow State University, Universitetskij prospekt 13, Moscow 119992, Russia

We report instrument capabilities and scientific goals of the TESIS experiment on board the satellite Coronas-Photon., which is planned for launching at the first half of 2008. The primary objective of the TESIS is to understand mechanisms of energy accumulation and release in the solar atmosphere through complex multiwavelengths observations of solar active phenomena with high spatial, spectral and temporal resolution. In the EUV and Soft X-ray spectral bands, TESIS will provide simultaneous imaging of the Sun with five instruments: the MgXII Imaging Spectroheliometer (MISH) for monochromatic observations of the full Sun in the MgXII 8.42 A line; EUV Spectoheliometer (EUSH) for registration of solar spectra in the band 280-330 A; two Full-disk EUV Telescopes (FET) with multilayer mirrors covering the band 130-136 A and 290-320 A and Solar EUV Coronagraph (SEC) for observations the inner and outer solar corona from 0.2 to 4 solar radiuses in spectral band 290-320 A. The design of the instrument and scientific program of observations are discussed.


presentation   (6.6 MB)




High energy gamma-ray spectrometer NATALYA-2M for satellite mission Coronas-Photon

E. Lupar

IAF, MEPHI, Moscow, Russia

Спектрометр высокоэнергичных излучений “Наталья-2М” входит в состав комплекса научной аппаратуры спутника “КОРОНАС-ФОТОН”. Прибор "Наталья-2М" предназначен для проведения следующих измерений:
- изучения временного поведения интенсивности и энергетических спектров жесткого электромагнитного излучения солнечного и космического происхождения в широком энергетическом диапазоне от 0,3 до 2000 МэВ;
- выделение «нейтронных» событий солнечного происхождения с энергиями 20 - 300 МэВ.
Регистрирующий блок прибора “Наталья-2М” состоит из набора 16 сцинтилляционных модулей CsI(Tl) размером 360 x 80 x 45мм каждый. Модули уложены в четыре слоя, соседние слои повернуты относительно друг друга на 90°. События, связанные с фоном заряженных частиц, исключаются при помощи пластмассовых сцинтилляционных детекторов.
Эффективность регистрации прибором гамма-излучения определялась расчетным путем методом Монте-Карло. Стабильность параметров спектрометра обеспечивается системой стабилизации усиления, включающей эталонный световой источник и узлы регулировки усиления каждого ФЭУ спектрометра. Проведенные с системой стабилизации измерения показали, что она обеспечивает стабильность спектрометрического тракта лучше 0,1% при загрузках до 3 x 104 имп/сек и при изменениях положения спектрометра в магнитном поле Земли. Для калибровки энергетической шкалы в полете в состав прибора введен калибровочный источник "меченых" γ-квантов. Полученное на технологическом образце энергетическое разрешение МэВ не хуже 9% для линии Еγ = 0,662.


presentation   (1.4 MB)




Low energy payload of Solar X-ray Spectrometer (SOXS) mission. Instrument description and first results

T. Mrozek

Astronomical Institute, Wrocław University, Wrocław, Poland

Solar X-ray Spectrometer (SOXS) onboard GSAT-2 Indian satellite was launched on 8 May 2003. The low energy module (SLD) of the instrument is built up with two solid state detectors - Si PIN and Cadmium-Zinc Telluride (CZT). The dynamic energy ranges for detectors are 4-25 keV (area 11.56 mm^2) and 4-56 keV (area 25 mm^2), respectively. Both detectors have superb temporal resolution (100 ms in the flare mode) as well as energy resolution of 0.8 keV for Si PIN and 1.7 keV for CZT. These parameters allow for analysis of the intensity, peak energy and equivalent width of the Fe-line complex at 6.7 keV and iron-nickel complex at 8 keV. The description of the instrument, its in-orbit performance and first results will be presented.


presentation   (3.7 MB)




Dependence of count statistics on data collection time

S. Płocieniak

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

It is always recommended to check whether the desired data gather intervals (DGI) are optimum in the sense of expected count statistics. We investigated this problem is some details. In order to properly simulate statistical nature of events expected to be seen within given DGI (counts in the detector), selected different random event generators (REG) or random number generators (RNG) can be employed in the numerical exercises. REG used in the SphinX experiment planning will be presented. It has been used in order to model the statistical character of events from non-stationary sources, for which the intensity is changing in characteristic times (tau) much shorter than DGI. Depending on tau, the most favorable detection strategies are proposed.


presentation   (140 KB)




X-ray fluorescence: a positive use in SphinX

S. Płocieniak

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

Fluorescence emission coming from various parts of the instrument was usually a big problem in construction of X-ray instruments. It comes out as a result of illumination of crystals, foils etc through a direct harder component of solar X-ray emission as well as from energetic particles penetrating the inside of the instrument. SphinX design is optimized in order to keep these unwanted fluorescence emission low. In addition, we are making use of the fluorescence in a new, positive way by incorporating the process for in-flight energy calibration of the detectors gain and for new-concept narrow-band solar photometry. We present principles and details of these new designs and estimate expected rates to be observed for selected solar activity levels.


presentation   (140 KB)




SphinX electronic delay times and priorities

P. Podgórski

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

Various dead times present within the SphinX detectors and electronics cause related biases into the measured response. I will discuss in particular the effects being introduced due to the pile-up and electronics. Special attention will be given to the pulse-shaping amplifier used in SphinX. The examples will be presented how this amplifier responds to the regular sequences of test signals.


presentation   (675 KB)




Envisaging SphinX: forward modeling of X-ray spectra

M. Siarkowski

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

Based on the expected temperature and emission measure for given solar activity level we calculated the corresponding fluxes and spectra which should be observed by SphinX. In the calculations we have taken into account all proposed filters and detector transmissions as well as detector efficiency. The results are used to estimate the optimal entrance apertures to keep the fluxes below ~50 000 c/s for all possible levels of flare activity.


presentation   (930 KB)




Envisaging SphinX - the elemental abundance determinations

B. Sylwester

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

We envisage the possibility of establishing the absolute abundance of Fe, Ca, Ar, S, Si and Mg based on the data to be obtained with SphinX. In the abundance determination we will use the method of fitting the theoretical spectra coming from model calculations to the observed ones. In the spectra calculation routines we will allow for the dependence of line and continuum emission on varying chemical composition of source plasma. The analysis will be made for individual energy intervals containing groups of prominent lines of specific elements. It will be shown that the abundances of Fe, Ca and Ar can be determine only when the Sun becomes more active.


presentation   (1.5 MB)




SphinX: the ideas behind the Project

J. Sylwester and the SphinX Team

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

The rationale of SphinX will be given together with a short description of considerations which led us up towards the present construction of the instrument. Important new concepts being introduced, concern as well as the principle of the measurements, method of taking the measurements and the physical problems which are to be addressed.


presentation   (4.9 MB)




SphinX ground-based software architecture

R. Sysala and M. Cupák

evolving systems consulting s.r.o. (Evolvsys.cz) and CupySoft, Praha, Czech Republic

The software architecture for ground based sector is introduced and main parts of the software are described. The purpose of software is to analyse and process incoming data dumps, downloaded from the S/C operation center. The inputs for the processing are SphinX spectrometer science (X-ray) data and auxiliary data - housekeeping/technological data and S/C position/orientation data. Processed data will be accessible locally using the interactive visualisation tool and remotely using web server (data catalogue and visualisation).


presentation   (2.4 MB)




SphinX detectors and their characteristics

W. Trzebiński

Space Research Centre PAS, Solar Physics Division, Wroclaw, Poland

The principles of the PIN detectors to be used in SphinX will be discussed. Their main characteristics will be presented. In particular diagrams of the energy resolution and sensitivity will be shown.


presentation   (340 KB)




Expected TESIS science outcome

A. Urnov

P.N.Lebedev Physics Institute of RAS, Russia

The capabilities and features of the TESIS instrumentation on board the Coronas-Photon spacecraft are considered from the viewpoint of current problems of atomic and plasma physics of solar corona. These problems include the location and mechanisms of energy release and its transformation into the heat, XUV radiation, charge particle beams and plasma motions. The interrelation of local transient processes connected with eruptive phenomena - flares, CME, dimmings etc., with global long-term structures persistent in corona is also an important subject of study. To anticipate possible scientific outcome from the TESIS experiment a short survey is given of the main approaches used in the preceding experiment SPIRIT on the CORONAS-F mission.
The main stress is made on the diagnostics techniques developed for a study of temporal and spatial dynamics of the temperature content of hot plasma structures necessary for understanding the formation mechanisms of soft X-ray emission. In particular an approach based on a consistent modeling of complex data from CORONAS-F, GOES and RESSI satellites, including the use of time series of monochromatic full-Sun images in the X-ray Mg XII 8.42 line and EUV lines, provided the spatial electron density and temperature distributions and their temporal evolution for long-duration events. The method used allowed to verify the absolute intercalibration of the fluxes recorded in all aforementioned experiments and to reference the Mg XII images to the solar disk. A study of elemental abundances as well as formation mechanisms of EUV emission was shown to be possible on the base of CHIANTI data bank.
Substantial improvements of spatial, spectral and temporal resolution in TESIS experiment as compared to SPIRIT one should allow to diagnose short-duration – impulsive and compact events, and to study fine structure of their temporal evolution and details of the energy budget. Comparison of EUV and X-ray DEM permits to reveal non-steady state plasma characteristics connected with transient ionization balance and non-Maxwellian phenomena. Full-Sun monochromatic XUV imaging spectroscopy of TESIS supported by other current extraterrestrial and ground-based observations has to provide experimental constraints sufficient for selection of possible mechanism and quantitative modeling of complex eruptive phenomena under study.


presentation   (8.3 KB)




Organization and schedule of Coronas-Photon manufacturing,
procedures of ground and pre-launch testing


Vitaly Yurov

IAF, MEPHI, Moscow, Russia




presentation   (42 MB)